1998 Lincoln Continental diagnostic download

You are searching repair manual in PDF format about 1998 Lincoln Continental diagnostic download use another keyword for search another post or files

  1998 Lincoln Continental diagnostic download Direct Download speed 5787 Kb/s

  1998 Lincoln Continental diagnostic download Full Version speed 6767 Kb/s

1999 Lincoln Continental Power Steering Pump REMOVAL


Filed Under (Lincoln) by admin on 14-09-2010

1. Remove the radiator upper sight shield. 2. Disconnect the power steering reservoir pump hose. 3. Raise the vehicle. 4. Remove the air conditioning compressor. 5. Remove the nut and the routing bracket. 6. Disconnect the power steering pressure hose. 1999 Lincoln Continental V8-4.6L DOHC VIN V 7. Remove the four bolts and the power steering pump. INSTALLATION 1. Follow the removal procedure in reverse order. 2. Install anew seal on the high pressure line fitting. 3. Fill and leak check the system.



Filed Under (repair and maintenance tips) by admin on 27-04-2010

1998-2002 Continental FORD: 1998-2006 Town Car 1996-1999 Taurus SHO 2000-2006 LS 1998-2006 Crown Victoria, Mustang
1998-2006 Navigator 2000 Taurus 2002-2003 Blackwood 2002-2005 Thunderbird 2003-2005 Aviator 2003-2006 Focus
2004-2006 Taurus MERCURY: 2005-2006 Five Hundred, Freestyle 1998-2006 Grand Marquis 1997-2006 E-Series, Expedition, F-150
2000 Sable 1999-2006 F-Super Duty 2004-2005 Sable 2000-2005 Excursion, F-53 2005-2006 Montego 2001-2006 Escape 2002-2005 Mountaineer 2002-2005 Explorer 2005-2006 Mariner 2005-2006 Escape Hybrid 2006 Mariner Hybrid LINCOLN: 1997-1998 Mark VIII This article supersedes TSB 04-16-01 to update the vehicle applications and model years.
EXPERIENCED. ISSUEnApproximately 50% of coil on plug (COP) coils returned for warranty do not have a problem.
ACTION The misfiring cylinder must be identified through Self-Test misfire codes or through WDS Power Balance. Rule out base engine problems, rule out fuel problems, and then look at ignition problems (be sure to rule out coil primary circuit issues).
Once the above steps have been completed, and the issue is in the secondary part of the ignition system, the oscilloscope procedure outlined in this TSB can isolate the difference between a coil or spark plug problem.

Ford / Mercury / Lincoln Band-Mounted Sensor Re-Learn Instructions


Filed Under (Ford, Lincoln) by admin on 17-10-2009

The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable

1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal


1998 Honda Passport Erasing ABS Diagnostic Trouble Codes (DTCs)


Filed Under (Honda) by admin on 13-10-2010

To erase anti-lock brake system (ABS) DTCs on 1998 Passports without the PGM Tester, use the procedure in this bulletin. The procedure in the 1998 Passport Service Manual is incorrect. NOTE: You can erase ABS DTCs with the PGM Tester when the SN811 software version becomes available. On page 5A-38 of the Service Manual, cross out step 3, “How to erase code,” and write on the page, “See S/B 97-084 for the ABS DTC erasing procedure.” 3. Using the two brown, male connectors from the Connector Test Adapter Kit (T/N J-35616-A), insert one into terminal 4 of the DLC, and the other into terminal 12 of the DLC. Then connect a jumper wire from the kit (any color) between the two connectors. REQUIRED SPECIAL TOOL Connector Test Adapter Kit: TIN J-35616-A ERASING ABS DTCs NOTE: 0 ABS DTCs cannot be erased by disconnecting the battery. Doing this procedure erases a// ABS DTCs (current and stored). 1. Turn the ignition switch OFF (0). 2. Under the driver’s side of the dashboard, locate the 16P DLC (data link connector). / JUMPERWIRE and CONNECl \ 4. Turn the ignition switch ON (II). (The ABS indicator light flashes the DTCs.) Let the light flash on and off at least once. 5. Using your hand, press the brake pedal until you hear the solenoid click, then release the pedal. Do this eight times within 3 seconds. 6. After you

2007 Chevrolet HHR Power Door Locks Inoperative Diagnostic


Filed Under (Chevrolet) by admin on 10-04-2011

Power Door Locks Inoperative Diagnostic Instructions • Perform the Diagnostic System Check – Vehicle prior to using this diagnostic procedure. • Review Strategy Based Diagnosis for an overview of the diagnostic approach. • Diagnostic Procedure Instructions provides an overview of each diagnostic category. Diagnostic Fault Information Circuit Switch Side Supply Voltage Relay Door Lock/Unlock Signal Door Latch Control Driver Door Lock Switch Ground Passenger Front Door Lock Switch Ground BCM Ground 1. Door Lock Malfunction 2. Door Lock Switch Malfunction Circuit/System Description The DR LCK fuse supplies battery positive voltage to the body control module BCM for the door lock system. The BCM supplies and monitors a reference voltage to the door lock switch through the door lock switch lock/unlock signal circuit. The door lock switch also receives a constant ground source. If a door lock switch is placed in the lock position, the reference voltage is taken directly to ground and the BCM senses 0.0 volts on the signal circuit. If a door lock switch is placed in the unlock position, the reference voltage is taken to ground through a 1.5k ohm resistor that is internal to the door lock switches and senses approximately 2.9 volts on the signal circuit. This is how the BCM determines what portion of the door lock switch was activated. The BCM, upon receipt of a door lock switch lock or unlock signal, will switch the appropriate door lock actuator control circuits to battery positive voltage. The opposing side of the door lock actuators are connected to ground internally within the BCM through the other door lock actuator control circuit and the doors will lock or unlock appropriately. Vehicles without keyless entry have two internal drivers in the BCM to control the door lock actuators. All door lock and all door unlock. Vehicles equipped with keyless entry have three internal drivers in the BCM. Driver door unlock, passenger door unlock and all door lock. This is done to isolate the driver door lock actuator so it can be unlocked by itself using the keyless entry transmitter.