2010 ford f150 mirror removal
You are searching repair manual in PDF format about 2010 ford f150 mirror removal use another keyword for search another post or files
2010 ford f150 mirror removal Direct Download speed 5787 Kb/s
2010 ford f150 mirror removal Full Version speed 6767 Kb/s
Filed Under (Toyota) by admin on 31-01-2011
hinges at the top of the mirror. Carefully pull at the bottom of the mirror until it unsnaps from the mirror mount. Tilt and lift the mirror out of the mirror housing. of the mirror. The heater wires are interchangeable. the bottom of the mirror sail. Separate the mirror housing from the mirror sail. 5 Unwrap the tape at the end of the mirror wire harness (seals it to the rubber sail gasket). This is required because the Signal® mirror wire will run through the rubber sail gasket in the same location. Pull away the rubber gasket from around the mirror sail. Remove the white plastic strain relief tab. Using the shorter of the two wire harnesses from the kit and starting from the inside of the mirror housing, route the wire through the mirror housing. You may need to use gopher wire to route the wire. Mirror Replacement Continued 8 9 Following along the existing factory wire, route the new wire through the mirror sail. Leave about 4 inches of wire in the mirror housing. Assemble the mirror housing and mirror. Replace the rubber gasket on the mirror sail. Remove any slack in the wire. Replace the strain relief tab. Connect the Signal® mirror mating connector to the Signal® mirror wire harness. If heated, connect the factory heater wires to the heater terminals on the Signal® mirror. NOTE: There is no polarity so the wires may be interchanged. 10 11 Tuck the wire harness behind the Signal® mirror. Align the hinges in the top of the mirror mount. Tilt the Signal® mirror down on the mirror mount. Press down on the bottom of the Signal® mirror until it snaps into position. Press down on all sides of the Signal® mirror to ensure proper operation.
Filed Under (Ford) by admin on 03-02-2011
1. Remove the front door trim panel (23942). Refer to Section 01-05. Peel back the water shield if necessary to gain access to the mirror wiring connector. 2. Disconnect the wiring connector. Remove rear view mirror mounting hole cover (17K709) located above the front door trim panel (inside window sail cover) by using a flat blade screwdriver to carefully pry off. 3. Remove the three nuts retaining the outside rear view mirror (17682) to the front door (20124). 4. Pull outside rear view mirror away from the front door while guiding the wiring out of the front door. 5. To install, reverse Removal procedure. Tighten nuts to 6-8 Nm (54-70 lb-in). Glass, Outside Mirror Removal NOTE: Power mirror and manual mirror glass replacement procedure ar similar. 1. Push in on the bottom of the glass until it stops. 2. Protect the mirror body with a rag or similar material at the top and insert a flat blade screwdriver between the mirror body and glass. 3. Pry on the glass until it snaps loose from motor assembly. Disconnect the heater wires from the glass, if equipped. 4. Remove the screwdriver and continue to pull the glass by hand until it is completely unsnapped from the motor assembly. Installation 1. Make sure the rubber gasket on the motor is properly installed on the motor assembly. 2. Reconnect heater wires to glass. 3. Position the glass assembly in the mirror, and push on the center of the glass to snap it in place. Push on glass until it is fully seated. Trim Cover Removal and Installation 1. Remove the rear view mirror mounting hole cover, located above the front door trim panel by using a flat blade screwdriver to carefully pry off. Care should be taken not to scratch paint. 2. To install, snap rear view mirror mounting hole cover into place. Be careful not to damage clips. Mirror Control Removal and Installation 1. Remove driver front door trim panel with mirror switch pigtail still attached to harness. 2. Reach around front door trim panel and disconnect switch harness from the main wire harness. 3. Using a small flat blade screwdriver, pry the outside rear view mirror control switch up from the front door trim panel. 4. Remove outside rear view mirror control (17B676).
Filed Under (Lincoln) by admin on 23-03-2011
Removal 1. Disconnect battery ground cable (14301) . 2. Remove front door trim panel . Refer to Section 01-05. 3. Remove outside rear view mirror inside mounting hole cover (17K709) from front door trim panel . 4. Disconnect outside rear view mirror assembly wiring connector and remove necessary wiring guides. 5. Remove plug button and remove the three mirror retaining nuts. Remove the outside rear view mirror while guiding the wiring and connector through the hole in the door. Installation 1. Install the outside rear view mirror assembly by routing the connector and wiring through the hole in the door and attach with three retaining nuts. Tighten to 4.5- 6.3 Nm (40-55 lb-in). Install plug button. 2. Connect mirror wiring connector and install wiring guides. 3. Install mirror outside rear view mirror inside mounting hole cover (snaps in). 4. Install front door trim panel . Refer to Section 01-05. 5. Connect battery ground cable. Glass, Outside Mirror Removal 1. Rotate outside rear view mirror glass to maximum upward travel. CAUTION: Use a piece of clean rag or similar material placed on the mirror shell to protect it from damage while removing the glass. 2. Insert a flat blade screwdriver between mirror shell and glass on bottom edge approximately one inch from inside corner at point A. 3. Place hand over outside rear view mirror glass to keep it from falling out and apply downward force on screwdriver until a snap is heard and glass is loose. 4. If glass is not loose, perform Steps 2 and 3 at point B.
Filed Under (Ford) by admin on 02-03-2011
Outside Rear View, Manual Removal 1. Remove the front door trim panel; refer to Section 501-05 . 2. Remove the rear view mirror mounting hole cover (17K709). 3. Remove the outside rear view mirror. 1. Remove the three outside rear view mirror nuts. 2. Remove the outside rear view mirror. Installation 1. To install, reverse the removal procedure. Outside Rear View, Power Removal 1. Disconnect the battery ground cable (14301). 2. Remove the front door trim panel; refer to Section 501-05 . 3. Remove the outside rear view mirror trim cover. 4. Remove the outside rear view mirror. 1. Disconnect the power mirror electrical connector. 2. Disconnect the power mirror wiring clips. 3. Remove the three outside rear view mirror nuts. 4. Remove the outside rear view mirror. Feed the power mirror wiring through the opening in the front door (20124). Installation 1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy. To install, reverse the removal procedure.
Filed Under (Ford, Lincoln) by admin on 17-10-2009
The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable
1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal