93 hyundai excel timing diagram


You are searching repair manual in PDF format about 93 hyundai excel timing diagram use another keyword for search another post or files



  93 hyundai excel timing diagram Direct Download speed 5787 Kb/s

  93 hyundai excel timing diagram Full Version speed 6767 Kb/s




1999 Hyundai Tiburon HYUNDAI’ ’1.8L & 2.0L 4-Cylinder – 1996-04 (Except Sonata & 2004 Elantra) TIMING BELT REMOVAL & INSTALLATION

0

Filed Under (Hyundai) by admin on 06-04-2010

download
TIMING BELT Removal
1. Remove all drive belts and drive pulleys from crankshaft and water pump. Remove generator bolt, if necessary. Remove crankshaft pulley and water pump pulley. 2. Remove timing belt covers and gaskets, noting bolt lengths and locations. DO NOT rotate engine counterclockwise, as viewed from timing belt side of engine. Remove timing belt tensioner pulley. 3. Rotate engine clockwise to align all timing marks so No. 1 cylinder is at TDC of compression stroke. See Fig. 1 . If reusing belt, place mark on timing belt to indicate direction of belt rotation. Remove belt. CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.

Related entry:

Elantra AC belt tensioner will not rotate, 2005 hyunda h100 scematic assembly diagram front timing belt alternater ect, adjusting alternator belts on hyundai h100, alternator belt for hyundai excel 1998, elantra ac tensioner, how to replair opel oring, hyundai matrix timing mark, p0449 tiburon 2005,

1996-2000 Hyundai Accent/ Hyundai Pony/ Hyundai Excel Trouble code identification

0

Filed Under (Hyundai) by admin on 07-06-2010

download
Idle air control (IAC) valve – circuit malfunction Wiring, IAC valve, ECM Injector 2 or 3 – circuit malfunction Wiring, injector Mass air flow (MAF) sensor – circuit malfunction Wiring, MAF sensor, ECM Idle air control (IAC) valve – circuit malfunction Wiring, IAC valve, ECM Wiring, HO2S, mechanical fault, fuel system, fuel Heated oxygen sensor (HO2S) – malfunction pressure, ECM AC cooling fan – circuit malfunction Wiring, AC cooling fan Idle air control (IAC) valve – circuit malfunction Wiring, IAC valve, ECM Engine coolant temperature (ECT) sensor – circuit malfunction Wiring, ECT sensor, ECM Intake air temperature (IAT) sensor – circuit malfunction Wiring, IAT sensor, ECM

Related entry:

crank sensor wire diagram for 2001 accent, 2006 hyundai sonata v6 code p2422, p0120 code on hyundai xg300, lable wire diagram idle air sensor hyundai matrix, hyundai ix35 repair guide, p0112 hyundai accent 2003, routing of trunk cable /2001 hyundai sonata, electricall drawing of windscreen wiper of hyundai xcel sprint 95, hyundai getz warning symbols, hyundai santa fe crankshaft sensor wiring harness,

2003 TOYOTA TACOMA TIMING BELT INSTALLATION REMOVAL

0

Filed Under (Toyota) by admin on 13-01-2011

download
NOTICE: Always turn the crankshaft clockwise. (c) Check that the timing marks of the camshaft timing pul- leys and No.3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°). (d) Remove the crankshaft pulley bolt. IF REUSING TIMING BELT, CHECK INSTALLATION MARKS ON TIMING BELT Check that there are 3 installation marks and front mark on the timing belt. If the installation and front marks have disappeared, before re- moving the timing belt, place 3 new installation marks on the timing belt to match the timing marks of the timing pulleys, and place a new front mark on the timing belt. 18. 19. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt ten- sioner and dust boot. 20. REMOVE TIMING BELT 21. (a) REMOVE RH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 22. (a) REMOVE LH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 23. REMOVE NO.2 IDLER PULLEY Remove the bolt and idler pulley. 24. REMOVE NO.1 IDLER PULLEY Using a 10 mm hexagon wrench, remove the pivot bolt, idler pulley and plate washer. 25. REMOVE CRANKSHAFT TIMING PULLEY Remove the timing pulley. HINT: If the pulley cannot be removed by hand, use SST and a service bolt to remove the timing pulley. SST 09950–50011 (09951–05010, 09952–05010, 09953–05020, 09954–05011)

Related entry:

yhs-fullyhosted_003, 1998 cadillac catera timing marks, 2002 xterra timing marks, HOW TO SET TIMING ON 2005 DODGE SLT 3 7 LITER VIDEO, timing marks on 2007 suzuki forenza, 2003 hyundai accent cam timing marks, remove and install a 1998 toyota camry timing belt, timing marks on a toyota paseao, Timing nissan NA20 engine on YouTube, 2004 Chrysler Pacifica can you still be at top dead center and cranky and still be off the compression stroke,

1996 Mitsubishi Eclipse GS-T TIMING BELT & BALANCE SHAFT BELT Removal

0

Filed Under (Mitsubishi) by admin on 18-01-2011

download
1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. CAUTION: DO NOT rotate crankshaft counterclockwise. Ensure timing marks are aligned. If reusing timing belts, mark timing belts for direction of rotation. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. NOTE: Camshaft sprocket dowel pins will be in 12 o’clock position when timing marks are correctly aligned. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B”.

Related entry:

water pump replacement 1992 mitsubishi 4g64 sohc video, 1992 mitsubishi 4g64 engine balance shaft belt replacement, 1996 toyots rave 4 timing marks, 1997 Honda Accord LX 4 cylenda Timming belt marks, 2007 triton v6 timing belt, vw bkp balance shaft timing procedure, noah townace engine timing section, camshaft sprocket removal mitsubishi 4g64 1992 8v, picture 1992 mitsubishi 4g64 sohc crankshaft sprocket, water pump replacement 1992 mitsubishi 4g64 sohc,

1994 Ford Aerostar/Ranger/Explorer Camshaft Timing ADJUSTMENTS

0

Filed Under (Ford) by admin on 08-03-2011

download
Checking Timing An access plug is provided in the cam drive belt cover so that camshaft timing can be checked without removal of the cover or any other parts. 1. Remove the access plug from the cam drive belt cover. 2. Rotate the crankshaft so that the No. 1 piston is rising on compression stroke. 3. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TC mark on the belt cover. Always turn the engine in the direction of normal rotation (clockwise, as viewed from the front). Backward rotation may cause the timing belt to jump time, due to the arrangement of the belt tensioner. 4. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover. 5. Install the belt cover access plug. Adjusting Timing Belt SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Belt Tension Adjusting Tool T74P-6254-A 1. Remove the outer timing belt cover as outlined in this section. CAUTION: Attempting to adjust timing belt tension without loosening spring pivot bolt will break Crankshaft Belt Tension Adjusting Tool T74P-6254-A when relieving tension on the belt. 2. If belt timing or tension is incorrect, loosen timing belt spring pivot bolt. 3. Hold tensioner with Camshaft Belt Tension Adjusting Tool T74P-6254-A. 4. While holding tensioner, loosen adjusting bolt and gradually release spring tension. Loosening Timing Belt Tensioner, 2.3L Tool Number 8 — 5. Using adjusting tool, pry tensioner away from belt. While holding, tighten adjusting bolt. There should be no tension on belt. Camshaft Timing Belt, 2.3L I-4 Timing Mark on Camshaft Sprocket Remove the bolts holding the crankshaft position sensor in place and pull the sensor assembly free of the dowel pin. 7. Remove the crankshaft pulley , crankshaft pulley hub and timing belt guide. 8. Remove the drive belt and inspect it for wear or damage. If the belt is damaged, replace it. 9. Remove one spark plug from each cylinder. 10. If not done: a. Loosen tensioner adjusting bolt. b. Using Camshaft Belt Tension Adjusting Tool T74P-6254-A, pry tensioner clockwise against spring tension as far as possible. c. Tighten adjusting bolt to hold tensioner in released position. 11. Align crankshaft so number one piston is at TDC (top dead center) as indicated by timing mark. 12. Line up camshaft sprocket timing mark with inner timing belt cover timing mark and key is pointing down.

Related entry:

yhs-default, yhsm-imp1, 2008 ford edge timing belt or chain, how should the camshaft position be when the crankshaft is on its mark lexus is200 1G-fe, 4g33 timing marks, how to find compresion stroke on number one on 2005 hyundai tuson, 2000 toyota camry2 2liter timing belt diagram, 2000 volvo s40 timing belt replacement, diagram for 2005 chevy optra timing belt replacement, valve timing onk4m,