isuzu axiom pcm tcm location diagram


You are searching repair manual in PDF format about isuzu axiom pcm tcm location diagram use another keyword for search another post or files



  isuzu axiom pcm tcm location diagram Direct Download speed 5787 Kb/s

  isuzu axiom pcm tcm location diagram Full Version speed 6767 Kb/s




2002-2004 Isuzu Axiom A/T – Shift Lock Solenoid Replacement

0

Filed Under (Isuzu) by admin on 30-04-2011

download
TSB SB05-05-5004 Shift Lock Solenoid ISSUE DATE: MAY 2005 Affected Vehicles 2002-2004 Isuzu Axiom (UP) 1998-2004 Isuzu Rodeo (UE) and Rodeo Sport (UA) Service Information Use the following steps to remove and replace the Shift Lock Solenoid. Service Procedure 1. Access the Shift Lock Solenoid by removing the Center, Front, Rear Console Assemblies, Selector Lever Knob, and Cover Assembly. Refer to the Selector Lever section in the Service Manual. 2. Set parking brake, move Selector Lever to lowest gear, and remove the Shift Lock Cable. 3. Remove the two screws securing the Shift Lock Solenoid to the Selector Lever subassembly. Disconnect the Shift Lock Solenoid 2-pin connector. 4. Disconnect the 1-40 (Rodeo) or 1-3 (Axiom) six-pin connector and slide the female connector off bracket. Remove the Terminal Position Assurance (TPA) Lock from the connector. Locate the two blue wires in position 1 and 3 on the female connector. With appropriate tool (shown above), apply light pressure upward on the connector locking tab while gently pulling on the blue wire to release. Note :Never use force to remove a terminal from a connector. 5. Insert the two blues wires from the replacement Shift Lock Solenoid into the 1- 40 (Rodeo) or 1-3 (Axiom) female connector. It does not matter which blue wire is inserted into the 1 and 3 position. Gently tug the blue wires to make sure they are secure. NOTE :D iscard the extra 2-pin connector sub harness included with replacement Shift Lock Solenoid P/N 8-97181-068-2. 6. Reconnect the Shift Lock Solenoid 2-pin connector and reattach the two screws securing the Shift Lock Solenoid to the selector lever subassembly. 7. Reconnect the 1-40 (Rodeo) or 1-3 (Axiom) six-pin connector and slide the female connector onto the bracket. 8. Reinstall the Selector Lever Knob, Cover Assembly, Center, Front, and Rear Console Assemblies. Refer to the Selector Lever section in the Service Manual. 9. Check Shift Lock operation: a. With ignition key in “Lock” position, Selector lever should not move from “P” position. b. With ignition key in “ON” position and brake pedal depressed. Selector lever can be moved out of “P” position. c. Key can be removed only when turned to “LOCK” position and selector lever is in “P” position.

Related entry:

dodge transmission solenoid diagram, diagram of shit interlocking soliend for 94 mercury villager, location of shift solenoid on 2001 park avenue, 2005 cavalier shift solenoid, gear shift lock out buick lucerne, 2007 chevy impala shift lock, mercury grand marquee 1999 shift solenoid, how to replace a radiator on a 03 axiom, 2007 impla shift ovreride button, ford explorer shift interlock repair,

1995 Chevy Lumina APV Engine Control Module: Service and Repair

0

Filed Under (Chevrolet) by admin on 28-08-2010

download
CAUTION: To prevent possible Electrostatic Discharge damage to the Powertrain Control Module (PCM), Do Not touch the connector pins or soldered components on the circuit. Service of the PCM should normally consist of either replacement of the PCM or a Programmable Read Only Memory (PROM) change. If the diagnostic procedures call for the PCM to be replaced, the engine calibrator (PROM) and PCM should be checked first to see if they are the correct parts. If they are remove the PROM from the faulty PCM and install it in the new service PCM. THE SERVICE PCM WILL NOT CONTAIN A PROM. Diagnostic Trouble Code (DTC) 51 indicates the PROM is installed improperly or has malfunctioned. When DTC 51 is obtained, check the PROM installation for bent pins or pins not fully seated in the socket. If the PROM is installed correctly and DTC 51 still shows, replace the PROM. Important: When replacing the production PCM with a service PCM (controller), it is important to transfer the Broadcast code and production PCM number to the service PCM label. Please do not record on PCM cover. This will allow positive identification of PCM parts throughout the service life of the vehicle. CAUTION: To prevent internal PCM damage, the ignition must be “OFF” when disconnecting or reconnecting power to PCM (for example, battery cable, PCM pigtail, PCM fuse, jumper cables, etc.). REMOVE OR DISCONNECT 1. Negative battery cable. 2. Right side sound insulator. 3. Vacuum center. 4. Connectors to PCM. 5. PCM. 6. PROM access cover. 7. PROM from PCM. INSTALL OR CONNECT 1. PROM to PCM. 2. PROM access cover. 3. PCM. 4. Connectors to PCM. 5. Vacuum center. 6. Right side sound insulator. 7. Negative battery cable.

Related entry:

pcm for malibu 2004, 2003 neon pcm schematic, ecm fuse location in a 2005 chevy malibu, 2002 ford mustang air bag module download, 2001 ford mustang pcm location, gm 98 chev lumina if no power to read dlc how can you scan it, izusu pcm 2002, front end alignment spec for 1994 chev lumina, location of ford focus ecm groung, isuzu key pin search,

1997 Buick Riviera DTC P0341 Camshaft Position (CMP) Sensor Performance

0

Filed Under (Buick) by admin on 24-12-2010

download
The camshaft position PCM input is produced by the ignition control module. The ICM produces the camshaft position PCM input by filtering the camshaft position (CMP) sensor pulses when the engine is running and CKP sync pulses are also being received. The PCM uses the camshaft position PCM input pulses to initiate sequential fuel injection and to determine crankshaft position for the misfire diagnostic. The PCM constantly monitors the number of pulses on the camshaft position PCM input circuit and compares the number of camshaft position PCM input pulses to the number of 18X reference pulses and the number of 3X reference pulses being received. If the PCM receives an incorrect number of pulses on the camshaft position PCM input circuit, DTC P0341 will set and the PCM will initiate injector sequence without the camshaft position PCM input with a one in six chance that injector sequence is correct. The engine will continue to start and run normally, although the misfire diagnostic will be disabled. Conditions for Setting the DTC • The engine is running (3X reference pulses are being received). • The ratio of 3X reference pulses to Cam pulses received by the PCM does not equal 6. • The ratio of 3X reference pulses to 18X reference pulses received by the PCM equals 6. • The above conditions are present for 600 engine revolutions. Action Taken When the DTC Sets • The PCM will illuminate the MIL during the second consecutive trip cycle in which the diagnostic test has been run and failed. • The PCM will initiate injector sequence without the camshaft position signal with a one in six chance that injector sequence is correct. • If equipped with traction control, the PCM will command the EBTCM via serial data (CKT 800) to set an ABS/TCS DTC, the EBTCM will turn OFF traction control, and the EBTCM will illuminate the TRACTION OFF lamp. • The PCM will store conditions which were present when the DTC set as Freeze Frame and Fail Records data.

2006-2007 Ford Freestar DAMAGED SPARK PLUG ELECTRODE/ MIL DTC P030X

0

Filed Under (Ford) by admin on 02-03-2011

download
Some 2006-2007 Freestar and Monterey vehicles may experience a melted or damaged spark plug electrode, malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC’s) P030X, rough idle, engine knock/ping on acceleration. Pre-ignition (which yields these symptoms) may be caused by water entering the powertrain control module (PCM). ACTION: Follow the Service Procedure steps to correct the condition. SERVICE PROCEDURE 1. Remove PCM from vehicle. Refer to Workshop Manual (WSM), Section 303-14. 2. Remove the PCM cover by carefully bending back the four (4) retaining clips holding the galvanized metal cover to the top plate. (Figure 1) Figure 1 – Article 07-14-1 3. Look for evidence of water within the PCM (liquid water, rust, water stains or deposits). (Figure 2) If found – obtain a replacement PCM before continuing on to Step 4. If no water is found, continue on to step 4 with the vehicle’s original PCM. Figure 2 – Article 07-14-1 4. Set the PCM top plate in a clean, dry location where the circuitry will be protected from damage. 5. With the PCM cover removed, drill a 1/4″ hole on each of the four (4) corners of the PCM cover. Get as close to the corner as possible. (Figure 3) Figure 3 – Article 07-14-1 6. De-burr the edges on both inside and outside surfaces. (Figure 3) Be sure to vacuum off all chips and wipe off all metal dust and any machining oil. 7. Clean the surfaces of the PCM cover with Motorcraft ZC-21 (Metal Surface Cleaner) or equivalent. Also clean the edges of the PCM top plate. The metal surfaces must be completely clean before proceeding to Step 8. 8. Apply Motorcraft TA-29 Ultra Silicone Sealant to all edges depicted. (Figure 4, 5, 6, 7) Proceed directly to Step 9 – do not let the sealant skin over. NOTE: Motorcraft TA-32 can NOT be used since its constituents may damage the PCM circuitry.

Related entry:

2006 Ford Freestar PCM Replacement, 2005 ford freestar pcm how to, 2007 ford freestar pcm location, freestar pcm 2006, freestar pcm 2006 where to fine it, Location of PCM on 2005 ford freestar, pcm fuse freestyle,

2005-2006 Volkswagen Touareg Update Programming Transmission Control Module (TCM) for Improved Upshifting (OE)

0

Filed Under (volkswagen) by admin on 16-03-2011

download
Service Requirements: Vehicle must meet ALL of the following criteria. 1 – Procedure is valid only for vehicles that show the OE code in the OTIS View Campaign inquiry screen on the day of repair (see Page 11). 2 – Vehicle must be within the Limited New Vehicle Warranty. 3 – Procedure must be performed within the allotted time frame stated in this Technical Bulletin. Procedure: – Raise hood, inspect for white dot located on accessory drive belt tensioner. – If white dot is present, close out the Required Vehicle Update in O.T.I.S. Input appropriate code ( see page 11). – If white dot is not present, follow instructions to perform update programming (Flashing) of transmission control module. Note: When performing the reflash procedure, ALL DTCs for all systems are erased. DTCs linked to Guided Fault Finding function tests will be lost. Therefore, always address stored DTCs for Customer concerns unrelated to the reflash procedure first. The following “Update – Programming” (flashing) process may overwrite any “TUNED” ECM or TCM programming.A “TUNED” ECM or TCM is described as any ECM or TCM altered so as to perform outside the normal parameters and specifications approved by Volkswagen of America, Inc. If you encounter a vehicle with a “Tuned” ECM or TCM, prior to performing the “Upda- te – Programming” (flashing) procedure: D Your Dealership should place the vehicle owner on notice in writing, that their ECM or TCM was found to have been tuned, and that any damage caused by the tuning of the ECM or TCM (including any adverse emissions consequences) will not be covered by Volkswagen of America, Inc. warranties.

Related entry:

download service manual vw touareg r5 tdi, reprogram 2005 vw touareg transmission control module, hiw to change the time in a touareg, how to install tcm for 2007 kia spectra,