system refrigerant capacity ford taurus
You are searching repair manual in PDF format about system refrigerant capacity ford taurus use another keyword for search another post or files
system refrigerant capacity ford taurus Direct Download speed 5787 Kb/s
system refrigerant capacity ford taurus Full Version speed 6767 Kb/s
Filed Under (Ford, Lincoln) by admin on 17-10-2009
The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable
1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal
Filed Under (Ford) by admin on 07-09-2010
FORD: 2005 Mustang 2004-2005 F-150 2005 Expedition, F-250, F-350 This article supersedes TSB 05-15-8 to update the Service Procedure. ISSUE Some vehicles equipped with a 4.6L 3-valve or 5.4L 3-valve engine may exhibit a ticking and/or knocking noise after reaching normal operating temperature. The noise may be described as “ticks”, “taps”, “knocks”, or “thumps”. In some cases the noise may be a normal characteristic of these engines. In other cases the noise may require further investigation. Sorting out and defining the noise as reported by the customer is important to successfully diagnose and/or repair the condition. ACTION Before starting diagnosis, it is critical to determine the specific engine noise the customer is concerned with. The customer should be interviewed to get their detailed perception and description of the noise, and to determine if the noise occurs at idle or above idle speed, and if the engine is cold, hot, or both. Attempt to duplicate the noise, and determine the source of the symptom. Refer to the following Service Procedure to help determine the source of the noise and if a repair is needed. LINCOLN: 2005 Navigator PRE-CHECKS 1. 2. 3.
Filed Under (Toyota) by admin on 15-06-2010
1995-96 A/C Compressor Refrigerant Oil Checking All Models * PLEASE READ THIS FIRST * CAUTION: DO NOT exceed A/C system refrigerant oil capacity, when servicing system. See REFRIGERANT OIL & REFRIGERANT SPECIFICATIONS. See the COMPRESSOR SERVICING article for compressor servicing procedures. SERVICING PRECAUTIONS DISCHARGING SYSTEM Discharge A/C system, using approved refrigerant recovery/recycling equipment. Always follow recovery/recycling equipment manufacturer’s instructions. After refrigerant recovery process is completed, the amount of compressor oil removed must be measured and the same amount added to A/C system. DISCONNECTING LINES & FITTINGS After system is discharged, carefully clean area around all fittings to be opened. Always use 2 wrenches when tightening or loosening fittings. Some refrigerant lines are connected with a coupling. Special tools may be required to disconnect lines. Cap or plug all openings as soon as lines are removed. Remove caps until connections of lines and fittings are to be completed. CONNECTING LINES & FITTINGS
Filed Under (Ford) by admin on 17-04-2010
Fault Idle would intermittently rev up to 4000 rpm. Car would also accelerate on its own up to around 3000 rpm when driven off. If clutch depressed during this time while driving, the engine would rev up to 4000 rpm.
The Ford EECV engine management system ECM requires reprogramming. Vehicles Rectification
At present the vehicle needs to be returned to a Ford dealer for the engine management ECM to be reprogrammed using dedicated equipment. It has been noted that affected Ford EECV engine management ECMs have a part no. 97FB-12A650-ASA. Later Ford EECV engine management ECMs have a part no. 97 -12A650-AFC. After the original Ford EECV engine management ECM has been reprogrammed, the Ford dealer should tag the Ford EECV ECM with the new part number
Filed Under (Ford) by admin on 05-09-2010
FORD: Crown Victoria, Taurus Ford GT Mustang Ranger Expedition Explorer This article supersedes TSB 04-25-1 to update the vehicle model years. ISSUE Some vehicles may exhibit a bubbling or blistering under the paint on aluminum body parts. This is due to iron contamination of the aluminum panel. 1. Corrosion should be removed by blasting. Use an aggressive blasting material, such as acrylic (salt grain size). 2. Use a DA sander with 180 grit paper backed abrasive. Only sand and featheredge the damaged area. 3. Mix and apply Ford approved epoxy primer, per the manufacturer’s label instructions. Bake at 140° F (60° C), or use an infra-red lamp for curing. 4. If necessary, mix and apply two-part polyester filler to a slight over crown. Allow polyester filler to cure 20-30 minutes, or mix and apply spray polyester filler two-three (2-3) coats as necessary. Allow to cure per manufacturer’s label instructions. 5. Hand-sand the repair area with 80 grit sand paper to remove excess filler. 6. Finish-sand the repair area with 400 grit sand paper. 7. Mix and apply Ford approved primer/surfacer per manufacturer’s label instructions. Bake at 140° F (60° C) or use infra-red lamp for curing.